Wichita, KS · South Central Kansas
Metal Roof Cost in Wichita
Metal Roof work in Wichita, KS is modelled here at $7,800–$52,500, with the middle of that band around $20,500. That is the national range for a metal roof multiplied by a 0.94 cost index for this metro, which puts Wichita about 6% below the national baseline.
The largest Kansas metro, with prevailing construction wages below the national middle. Modelled below baseline — though frequent storm work keeps crews busy and can firm up pricing seasonally.
Everything below explains what that index does and does not know. It is an estimate of where local labor, overhead and permitting sit relative to the national middle — it is not a feed of local quotes, and it cannot see your roof. The parts of this page worth more than the headline number are the local conditions further down and the component table, because those are what let you interrogate a real bid when you get one.
Estimated range — not a quote
Metal Roof Cost in Wichita, KS
Low end
$7,800
Typical
$20,500
High end
$52,500
What this covers: a complete metal re-roof including tear-off, underlayment, panels and the trim package.
Per roofing square (100 sq ft of roof surface)
$515–$1,875(typical $1,025)
Applied to a 15–28 square roof, which is where the job figures above come from. Your own square count beats any assumption we can make.
Modelled estimate. These figures come from national industry-typical ranges, not from quoted jobs, and no one has looked at your roof. Use them to sanity-check a bid — never as a substitute for one.
Where the Wichita number comes from
No mystery and no proprietary data: it is one multiplication, and we would rather show it than ask you to trust it. If you disagree with the index, substitute your own and redo the arithmetic — the whole model is one number wide.
national cost per square (typical) $1,100 Wichita cost index x 0.94 = $1,034/square -> shown as $1,025 assumed roof size (typical) 20 squares $1,100 x 20 sq x 0.94 $20,680 -> shown as $20,500 low 15 sq x $550/sq x 0.94 $7,755 -> shown as $7,800 high 28 sq x $2,000/sq x 0.94 $52,640 -> shown as $52,500
Each line is rounded independently before it is displayed, so multiplying two rounded figures together will not always land exactly on a third. That is a deliberate consequence of not printing modelled estimates to the dollar — the raw product is shown alongside each rounded figure so you can see the difference rather than wonder about it.
What the 0.94 index is
An editorial estimate that Wichita runs about 6% below the national baseline for this kind of work, i.e. subtract roughly 6%. It is derived from the general pattern of prevailing construction wages, site conditions and permitting overhead in markets of this type — not from collected local quotes, and not from a licensed location-factor dataset. If a local contractor tells you something different about this market, believe the contractor.
What actually matters in Wichita
Climate, geography and local building practice, all of which you can verify independently. You will not find an invented local statistic here — no made-up average roof size, no fabricated local job counts. Where we do not know something about Wichita specifically, we say the true general thing instead.
- ●Sits in a part of the Great Plains with high hail frequency; hail is the dominant roofing risk here rather than a periodic event.
- ●Impact-rated Class 4 shingles are far more commonly specified than in most of the country, and many carriers discount them — worth asking yours.
- ●Straight-line wind events and derechos are a recurring source of widespread damage.
- ●Wide seasonal temperature swings, from severe summer heat to hard winter freezes, cycle roofing materials hard.
- ●A very large share of local work is insurance-scoped, which shapes how contractors quote and how quickly they can schedule.
Timing and local demand
The season follows the storms. After a major hail event, local capacity is consumed for months and out-of-area crews arrive.
What the low, typical and high jobs look like
A range only helps if you know which end applies to you. These are the three jobs the Wichita numbers describe.
Low$7,800
exposed-fastener steel panel on a simple, walkable roof — the cheapest way to put metal on a house
Typical$20,500
a 24- or 26-gauge steel standing seam roof on an average home, concealed fasteners, factory finish
High$52,500
aluminium standing seam, or a complex roof with many hips, valleys and penetrations, where the custom trim and flashing work dominates the bill
How this work is priced
"Metal roof" is not one product. An exposed-fastener steel panel screwed straight through the face and a mechanically-seamed aluminium standing seam roof are both metal roofs, and one costs roughly three to four times the other. Almost every confusing metal roofing quote comes down to which of those two the contractor is actually bidding, so establish the panel type, gauge and fastening system before you compare anything.
The economic case for metal rests on service life rather than on price. A properly installed standing seam roof is generally expected to last 40 to 70 years against 20 to 30 for asphalt, which means one metal roof instead of two or three asphalt ones. Whether that is a good trade depends almost entirely on how long you intend to own the house, and the honest answer for a homeowner planning to move in five years is usually no.
What is and is not in the price
Most of the distance between two Wichita quotes is scope rather than margin. Compare both columns before deciding one contractor is expensive.
Normally included in the price
- ●Tear-off and disposal of the existing roof
- ●High-temperature synthetic underlayment
- ●Panels — either exposed-fastener or standing seam, in the specified gauge and finish
- ●Clips or fasteners appropriate to the system
- ●Ridge, hip, eave, rake and valley trim
- ●Pipe flashings rated for metal
- ●Sealants and closure strips
Normally billed separately
- ●Snow retention — bars or guards, commonly $10 to $30 per linear foot
- ●Decking replacement or new solid sheathing where the roof was over purlins
- ●Gutters, which often need replacing to suit the new trim
- ●Additional insulation or a ventilated batten assembly
- ●Removal and reinstallation of solar
What pushes a Wichita job to the top of the range
Standing seam instead of exposed fastener
Concealed clips let the panel expand and contract without wallowing out screw holes, which is the failure mode of exposed-fastener roofs. It is the better system and it typically doubles the material and labor cost.
Aluminium, copper or zinc rather than steel
Aluminium runs meaningfully above steel and is the usual choice within a few miles of salt water. Copper and zinc are architectural products priced far above this model's range — treat any copper quote as outside these bands.
A complex roof
Metal punishes complexity more than asphalt does. Every hip, valley, dormer and penetration is a custom-bent, hand-fitted detail, and on a cut-up roof the trim work can approach the panel cost.
Heavier gauge and premium coatings
A 24-gauge panel in a PVDF finish costs more than 29-gauge in a polyester finish, holds colour longer and dents less. On a visible roof it is usually worth the difference.
Site-formed panels and long runs
Panels roll-formed on site avoid seams on long slopes but require the machine, the operator and the room to run it. Access constraints show up directly in the price.
What keeps it at the bottom
Exposed-fastener panel on a simple roof
On a barn, a shop, a porch or a plain gable where appearance is secondary, exposed-fastener steel is a legitimate and inexpensive choice. Budget for re-screwing it at some point.
Long, uninterrupted slopes
A simple gable is the ideal metal roof. Fewer cuts, fewer terminations, faster install, less waste.
Going over existing shingles where code allows
Some assemblies permit metal over a single sound layer of asphalt, saving the tear-off. Verify with your building department and with the panel manufacturer, because doing it against the installation instructions can void the finish warranty.
Component costs in Wichita
National component ranges with the 0.94 Wichita index applied. These are the lines a quote is built from — the most useful page on this site to have open while you read a bid.
| Line item | Range | Unit | Notes |
|---|---|---|---|
| Exposed-fastener steel panel, installed | $425–$750 | per square | Sometimes called ag panel or R-panel. Screws through the face. |
| Stone-coated steel shingle or tile profile | $750–$1,300 | per square | Mimics tile or shake; interlocking panels. |
| Steel standing seam, 24–26 gauge | $950–$1,700 | per square | Concealed clips. The mainstream residential standing seam choice. |
| Aluminium standing seam | $1,100–$2,100 | per square | Preferred in coastal salt-spray environments. |
| Copper or zinc standing seam | $1,900–$4,200 | per square | Architectural product. Outside this model's range — shown for scale only. |
| Trim and flashing package | $7.50–$19 | per linear ft | Ridge, hip, eave, rake, valley. Dominates the bill on a cut-up roof. |
| Tear-off before metal | $95–$200 | per square | Same as for asphalt; sometimes avoidable where code permits an overlay. |
| High-temperature underlayment | $40–$85 | per square | Metal runs hotter than asphalt; standard synthetic is not always rated for it. |
| Snow retention bars | $9.50–$28 | per linear ft | Not optional above entries and walkways in snow country. |
National baseline component ranges. Establish panel type and gauge first — it moves the number more than anything else on this list. Adjusted for Wichita, KS at a 0.94 index and rounded.
Size your own roof before you read a quote
Every number in this guide is priced against roof area, and roof area is not house area. Put your footprint dimensions and your pitch into the squares calculator and you will know how many squares you are buying — which turns a vague estimate into arithmetic you can check against a bid.
Getting a real quote in Wichita
Everything above is a model. The number that decides your budget is a written quote from someone who has been on your roof, and you want three of them scoped alike — same material line, same underlayment, same flashing treatment, and the per-sheet decking rate written down before the tear-off starts.
Roofing contractors in Wichita
Browse roofing companies listed in Wichita, KS, compare Google review scores, and contact them directly.
All Kansas roofing contractors
Browse by city across Kansas — useful if your job sits between metros or you want contractors from a neighbouring market to bid.
- ●Check licensing yourself. Our listings are compiled from public records. Confirm any contractor’s licence and insurance with the Kansas licensing board before work begins, and ask for a certificate of insurance sent directly from the insurer rather than a copy from the contractor.
- ●Compare scope, not just totals. The cheapest bid is often the one that left something out. Line up the three quotes against the component table above and find out what differs.
- ●Get the decking rate in writing. It is the one cost nobody can see before the tear-off, and it is the change order that surprises people. Agree the per-sheet price and an approval threshold before the job starts.
Other roofing costs in Wichita
Roof Replacement in Wichita
$5,300–$25,500 estimated
Full tear-off and re-roof in architectural asphalt shingle — the job most homeowners mean when they say "new roof". Priced per square, with the size assumptions shown.
Roof Repair in Wichita
$225–$3,300 estimated
Localized fixes — leaks, flashing, boots, valleys, a section of shingles. Priced per visit rather than per square, because that is how the trade actually sells it.
Flat & Low-Slope in Wichita
$3,400–$33,000 estimated
Single-ply membrane — TPO, EPDM and PVC — plus modified bitumen. Covers whole low-slope roofs and the flat sections over additions, porches and dormers.
Storm & Hail Damage in Wichita
$425–$11,500 estimated
Wind, hail and impact damage — from a tarp on the night of the storm to a full insurance-scoped replacement. The one topic where the price you pay and the price of the work are usually different numbers.
Tear-Off & Disposal in Wichita
$1,400–$8,500 estimated
Stripping and hauling away the existing roof — the line item that is usually bundled into a replacement quote and is worth pulling out and looking at on its own.
Decking & Sheathing in Wichita
$475–$13,000 estimated
Replacing sheathing under the shingles — the change order that surprises more homeowners than any other, because it cannot be quoted until the old roof is off.
Roof Inspection in Wichita
$0–$1,100 estimated
From the free look that comes with an estimate through to an infrared moisture scan or an engineer's report. Priced per visit, and often free — which is itself worth understanding.
Metal Roofing costs elsewhere in Kansas
Same model, different index. Comparing neighbouring markets is a quick way to see how much of a quote is the work and how much is the market it is being done in.
Common questions
Is a metal roof noisy in rain?
Not meaningfully, when it is installed over solid decking and underlayment with an insulated attic beneath — which describes essentially every residential installation. The noise reputation comes from panels screwed to open purlins over an uninsulated barn, where there is nothing between the panel and the space below.
Will a metal roof lower my insurance premium?
Sometimes. Many carriers discount impact-resistant and fire-resistant roofing, and metal often qualifies. The size of the discount varies by carrier and by state, and the only way to find out is to ask yours for the number in writing before you commit.
Does metal attract lightning?
No. A metal roof does not make a strike more likely. If anything it is favourable in a strike, because metal is non-combustible and conducts the energy across a large area rather than concentrating it.
How long does a metal roof actually last?
A steel standing seam roof with a quality coating is generally expected to run 40 to 70 years, and aluminium longer in coastal conditions. Exposed-fastener panels are the exception: the panel outlives its gaskets, and the screws typically need attention somewhere around the 15- to 20-year mark.
Can I put solar on a metal roof?
Standing seam is the best roof there is for solar — clamps grip the seam with no penetrations at all, which is both cheaper to mount and safer for the roof. Exposed-fastener panels require through-fastened mounts and the usual flashing care.
How we build these cost ranges
The short version: these are industry-typical ranges, not a quote.
For this page: the Wichita, KS cost index is 0.94, meaning we model this metro at about 6% below the national baseline. The largest Kansas metro, with prevailing construction wages below the national middle. Modelled below baseline — though frequent storm work keeps crews busy and can firm up pricing seasonally.
These are modelled ranges, not quotes
Every figure on this page is an estimate produced by a model, not a price anyone has been charged. We do not collect invoices, we do not receive bid data from contractors, and we do not have a feed of completed jobs. If you need a number you can rely on, the only source of one is a written quote from a contractor who has been on your roof.
Where the national ranges come from
The national baseline for each work type is an industry-typical installed-price band: the range that published cost guides, manufacturer installation literature and ordinary contractor pricing conventions broadly agree on for 2026. Each band is expressed low / typical / high, and where the work is genuinely sold by the square we show the per-square price and the roof size assumptions separately, so the whole-job figure can be re-derived rather than taken on trust.
Where the city adjustment comes from
Each metro carries a single cost index, with 1.00 meaning the national baseline. The index is our own editorial estimate of where local labor, overhead and permitting sit relative to the national middle, based on the well-established general pattern that construction costs run higher in large, high-wage, densely-built metros and lower in smaller ones. It is not a measured price feed, it is not a licensed location-factor dataset, and it is not derived from local quotes. The city figure is simply the national band multiplied by that index.
What we deliberately do not do
We do not publish invented local statistics. There is no "average roof size in your city" on this site, because we have not measured one. Local context here is limited to climate, geography and building-practice factors that are true of the region and that you can verify independently. We would rather be generic and correct than specific and made up.
Why the numbers are rounded
Modelled figures are rounded before display — to the nearest $500 above $10,000, the nearest $100 above $1,000, and more finely below that. A modelled estimate printed to the exact dollar is claiming a resolution it does not have. The rounding is the honest representation of how coarse these estimates really are.
What the model cannot see
It cannot see your pitch, your decking, how many layers are up there, how a truck reaches your house, what your local supplier quoted this month, or how booked the good crews are after the last storm. Those factors routinely move a real quote further than the entire spread between our low and high figures. Treat these ranges as a way to tell a plausible quote from an implausible one — nothing more than that.
A note on this particular topic
This band is deliberately the widest on the site because the product category is the widest. Do not read the midpoint as "the price of a metal roof" — read it as the price of a mainstream steel standing seam job, which is what the typical figure describes.
Cost model version 2026.08. Baselines and the regional index are reviewed periodically; the date shown on each page is the date that page's figures were last reviewed. Contractor listings on this site are compiled from public records — confirm any contractor’s licence and insurance with your state licensing board before work begins.
Get three quotes in Wichita
Every figure on this page is modelled. A written quote from a contractor who has been on your roof is the only number worth budgeting from — search roofing companies and contact them directly, free and with no middleman.