Georgia · 7 modeled metros
Roof Replacement Cost in Georgia
We model a full roof replacement in 7 Georgia metros. A typical job runs from about $10,000 in Columbus to about $11,500 in Alpharetta. Each figure is the national range for a full roof replacement multiplied by that metro's cost index, so the whole difference between two Georgia cities on this page is the index.
There is no single Georgia number here, on purpose. The model carries an index for each metro, not for the state, and averaging them would invent a figure nobody modeled. Outside these metros the national baseline applies.
Georgia metros side by side
| Metro | Index | Per square, typical | Typical job | Low – high |
|---|---|---|---|---|
| Columbus | 0.92× | $505 | $10,000 | $5,200–$25,000 |
| Macon | 0.92× | $505 | $10,000 | $5,200–$25,000 |
| Augusta | 0.93× | $510 | $10,000 | $5,200–$25,000 |
| Savannah | 1.00× | $550 | $11,000 | $5,600–$27,000 |
| Atlanta | 1.03× | $565 | $11,500 | $5,800–$28,000 |
| Marietta | 1.04× | $570 | $11,500 | $5,900–$28,000 |
| Alpharetta | 1.06× | $585 | $11,500 | $6,000–$28,500 |
Modeled estimates, rounded. Job figures assume a 15–30 square roof (20 for the typical case): a complete tear-off and re-roof in architectural asphalt shingle, including underlayment, drip edge, flashing and ridge cap. Each city name opens that metro’s full guide with the arithmetic shown.
Why the Georgia figures differ
Each index is our editorial estimate of where local labor, overhead and permitting sit against the national middle — not a feed of local quotes. Here is the reasoning for each, as stated on its guide.
Columbus0.92 · about 8% below the national baseline
A smaller west Georgia market on the Alabama line, with the lowest prevailing construction costs among the Georgia metros modeled here. Modeled well below baseline.
Macon0.92 · about 8% below the national baseline
A middle Georgia market with construction wages well below the Atlanta level. Modeled well below baseline.
Augusta0.93 · about 7% below the national baseline
A mid-size market on the South Carolina line with prevailing construction wages well below the large-metro level. Modeled below baseline.
Savannah1.00 · at the national baseline
A coastal market where higher wind-zone requirements offset otherwise moderate regional wages. Modeled at baseline.
Atlanta1.03 · about 3% above the national baseline
The largest metro in the Southeast, with construction wages modestly above the national middle and significant traffic and access overhead across a sprawling service area. Modeled above baseline.
Marietta1.04 · about 4% above the national baseline
An established inner-suburban Cobb County market inside the Atlanta labor pool. Modeled slightly above baseline.
Alpharetta1.06 · about 6% above the national baseline
An affluent north-metro submarket where larger homes, complex rooflines and higher-specification work push the effective cost above the Atlanta average. Modeled above baseline.
Who may do the work in Georgia
No state license — local only
Georgia does NOT license roofing contractors at state level. Under O.C.G.A. § 43-41-17, specialty contractors who contract with an owner to perform limited, specialty or specific trade work do not have to hold a residential or general contractor license when working within their specialty, and the State Licensing Board's own Traditional Specialty Contractors policy statement lists Flat Roofing, Sheet Metal Roofing, Shingles and Shakes, and Gutters and Downspouts among those specialties. The Board files these under "Exempt Specialty Contractors." What Georgia roofers actually need instead: local business licensing/registration where the city or county requires it, building permits, general liability insurance (a commercial and customer expectation rather than a state licensing condition), workers' compensation once they have three or more employees, and compliance with the state minimum construction codes. Board rules Chapter 553 cover only the residential and general contractor divisions — there is no roofing classification to apply for.
Sources: Georgia SOS — Traditional Specialty Contractors Policy Statements (lists Flat Roofing, Sheet Metal Roofing, Shingles and Shakes; quotes O.C.G.A. § 43-41-17) · Georgia SOS — Residential and Commercial General Contractor Exemptions ("Exempt Specialty Contractors") · Georgia SOS — Residential and Commercial General Contractors FAQ ("licenses are not required to perform work that qualifies as a specialty trade"; reciprocity; insurance) · Georgia Rules and Regulations Chapter 553 — State Licensing Board for Residential and General Contractors (residential and general divisions only) · Georgia SOS — State Licensing Board for Residential and Commercial General Contractors. Checked August 2026. Full Georgia licensing rules
Storm season and what it does to scheduling
Peak season: March–May, plus August–October for tropical systems. Georgia carries a spring severe season driven by Gulf moisture and a secondary late-autumn one, with damaging straight-line wind and hail the routine roofing events. From late summer into autumn the state is also in the inland track of Atlantic tropical systems, which arrive weakened but still deliver hours of wind and sideways rain. North Georgia adds occasional winter ice, where the falling-limb risk outweighs the load.
The weather that generates roofing work here: straight-line wind, hail, tropical systems, tornado. After a regional hail or wind event, local crews are booked for months and prices firm up; the off-season is where scheduling flexibility is worth money.
NOAA’s Storm Events Database records 10,877 county-level severe-weather events in Georgia from 2016 to 2026, including 928 hail reports of 1.00 in or larger. The most recent data year is partial. NOAA publishes storm reports on a rolling basis and the final months are still being processed, so a low count in the last year is not evidence of a quiet year. Source: NOAA NCEI
Georgia storm centerSize your own roof before you read a quote
Every number in this guide is priced against roof area, and roof area is not house area. Put your footprint dimensions and your pitch into the squares calculator and you will know how many squares you are buying — which turns a vague estimate into arithmetic you can check against a bid.
Getting a real quote in Georgia
Everything above is a model. The number that decides your budget is a written quote from someone who has been on your roof — three of them, scoped alike, with the per-sheet decking rate written down before the tear-off starts.
Georgia roofing contractors, by city
- ●Read the national guide for the detail. What is and is not in a replacement price, what pushes a job to the top of the band and the component costs are on the national roof replacement cost guide, and each metro guide applies its index to them.
- ●Compare scope, not just totals. The cheapest bid is often the one that left something out.
How we build these cost ranges
The short version: these are industry-typical ranges, not a quote.
For this page: 7 Georgia metros, indexed from 0.92 (Columbus) to 1.06 (Alpharetta). There is no state-level index.
These are modeled ranges, not quotes
Every figure on this page is an estimate produced by a model, not a price anyone has been charged. We do not collect invoices, we do not receive bid data from contractors, and we do not have a feed of completed jobs. If you need a number you can rely on, the only source of one is a written quote from a contractor who has been on your roof.
Where the national ranges come from
The national baseline for each work type is an industry-typical installed-price band: the range that published cost guides, manufacturer installation literature and ordinary contractor pricing conventions broadly agree on for 2026. Each band is expressed low / typical / high, and where the work is genuinely sold by the square we show the per-square price and the roof size assumptions separately, so the whole-job figure can be re-derived rather than taken on trust.
Where the city adjustment comes from
Each metro carries a single cost index, with 1.00 meaning the national baseline. The index is our own editorial estimate of where local labor, overhead and permitting sit relative to the national middle, based on the well-established general pattern that construction costs run higher in large, high-wage, densely-built metros and lower in smaller ones. It is not a measured price feed, it is not a licensed location-factor dataset, and it is not derived from local quotes. The city figure is simply the national band multiplied by that index.
What we deliberately do not do
We do not publish invented local statistics. There is no "average roof size in your city" on this site, because we have not measured one. Local context here is limited to climate, geography and building-practice factors that are true of the region and that you can verify independently. We would rather be generic and correct than specific and made up.
Why the numbers are rounded
Modeled figures are rounded before display — to the nearest $500 above $10,000, the nearest $100 above $1,000, and more finely below that. A modeled estimate printed to the exact dollar is claiming a resolution it does not have. The rounding is the honest representation of how coarse these estimates really are.
What the model cannot see
It cannot see your pitch, your decking, how many layers are up there, how a truck reaches your house, what your local supplier quoted this month, or how booked the good crews are after the last storm. Those factors routinely move a real quote further than the entire spread between our low and high figures. Treat these ranges as a way to tell a plausible quote from an implausible one — nothing more than that.
A note on this particular topic
The per-job range spans different roof sizes as well as different unit prices, which is why it is wide. A small simple roof at the low unit price and a large steep roof at the high unit price are both real jobs, and they are genuinely five figures apart.
Cost model version 2026.08. Baselines and the regional index are reviewed periodically; the date shown on each page is the date that page's figures were last reviewed. Contractor listings on this site are compiled from public records — confirm any contractor’s license and insurance with your state licensing board before work begins.
Get three quotes in Georgia
Every figure on this page is modeled. A written quote from a contractor who has been on your roof is the only number worth budgeting from.