StrongSeam AG Panel Through-Fastener Installation Manual

StrongSeam AG Panel Through-Fastener Installation Manual Jan 2016 3/4 36” COVERAGE UL90 #169 29 ga. & 26 ga. UL2218 Class IV/Impact UL790 Class A/Fire Tulsa, OK • Kansas City, KS • www.metalpanelsinc.com • 866-674-7657 Design This manual contains guidelines for installing Metal Panels Inc. AG panels and trim. Guidelines presented herein were in effect as of this printing. Metal Panels Inc. reserves the right to change designs or specifications at any time in order to stay current with building code requirements. To ensure that you have the latest information, please contact your sales representative at Metal Panels Inc. Application and design illustrations are for your reference only, and may not be appropriate or specified for all environments, conditions or building designs. It is strongly recommended that all projects should be engineered and installed to conform to applicable building codes, regulations and accepted industry practices. A roof must be designed to support certain minimum wind and snow loads. Consult local building officials to determine appropriate design load requirements. All roof systems should be designed or verified by a qualified engineer. It is the buyer’s responsibility to verify all code requirements, checking all measurements, and determine suitability of the product for the job. The buyer is responsible for supplying and confirming all panel and trim profiles, and actual length and quantities needed. All MPI instructions for this panel assume that a qualified firm or individual has been contracted to install this product. Failure to comply with stated recommendations voids all manufacturer responsibility for any damage or deterioration due to misuse of the product and voids any applicable warranty. TABLE OF CONTENTS AG Panel Profile ………………………………………………………………………. 1 Design Guidelines ……………………………………………………………………. 2 Introduction to Installation ……………………………………………………………. 4 Storage & Handling …………………………………………………………………… 6 Design & Installation ………………………………………………………………….. 11 Standard Trim ………………………………………………………………………….. 12 Accessories ……………………………………………………………………………. 13 Preliminary Installation Guide ………………………………………………………… 15 Load Table ………………………………………………………………………………. 17 Roof Installation Options ……………………………………………………………… 18 Visual Guide: Drip …………………………………………………………………….. 20 Visual Guide: Rake …………………………………………………………………… 21 Visual Guide: Valley …………………………………………………………………… 22 Visual Guide: Ridge Cap ……………………………………………………………… 23 Visual Guide: Sidewall ………………………………………………………………… 24 Visual Guide: Endwall ………………………………………………………………… 25 Visual Guide: Gable Trim ……………………………………………………………... 26 Visual Guide: Pitch Change ………………………………………………………….. 27 Visual Guide: Peak Plate ……………………………………………………………… 28 Visual Guide: Inside Corner ………………………………………………………….. 29 Visual Guide: Fascia ………………………………………………………………….. 30 Visual Guide: Base ……………………………………………………………………. 31 Visual Guide: Rat Guard ……………………………………………………………… 32 Visual Guide: Soffit ……………………………………………………………………. 33 Visual Guide: Drip Cap ……………………………………………………………….. 34 Visual Guide: Double-Angle …………………………………………………………. 35 Introduction Recommended Tools The MPI StrongSeam AG Panel is a low-profile, ▪ Cordless Screw Gun economical panel solution for residential, ▪ Snips commercial and agricultural roofing or post frame buildings. AG panels are a very durable, ▪ Tape Measure high-value metal roofing system, and can be used for roofing, siding, soffits, mansards ▪ Electric Metal Shear or Circular Saw and fascias. StrongSeam AG Panels are ▪ Caulk Gun manufactured in 29 ga. and 26 ga., and are available in 16 stock colors plus galvalume in ▪ Pop Rivet Tool 29 ga., and 22 stock colors plus galvalume ▪ Chalk Line in 26 ga. (24 ga. panels available by special order.) Minimum recommended slope is 1:12 ▪ “Duckbill” Locking Pliers with sealant. ▪ Electrical Extension Cord Specifications Installer must have experience using the tools The StrongSeam AG Panel is available in 36” listed above for metal roofing installation. panel width, with 3/4” ribs on 9” centers. The Safety 1/16th inch striation-ribs add strength and reduce potential incidence of oil canning in Use extreme caution when walking on a metal panels. roof. Metal panels may become slippery, so Maximum panel lengths are constrained always wear shoes with non-slip soles. Avoid only by practical handling and transportation working on metal roofs during wet conditions. limitations, typically a maximum of 55 ft. Do not walk on a metal roof which does not StrongSeam AG Panels may be end lapped to have a solid deck beneath it. If you must, walk accommodate longer runs. on the purlins only. Always use appropriate safety harnesses. OSHA safety regulations fig. 1 should be complied with at all times. 3/4 36” COVERAGE 29 ga. & 26 ga. UL90 #169 Caution UL2218 Class IV/Impact (24 ga. special order only) UL790 Class A/Fire Always wear heavy gloves when working with Testing steel panels to avoid cuts from sharp edges. When power cutting or drilling steel panels, UL90 #169 Uplift Rating always wear safety glasses to prevent eye UL2218 Class IV/Impact Resistance injury from flying debris. UL790 Class A/Fire Resistance Production Lead Time Please consult your MPI sales representative for accurate order production time. Large orders, non-standard colors, special order 24 ga. panels or custom trim fabrication may require longer lead times. Packaging For standard orders, panels are bundled for truck shipment. Custom shipping requirements may be accommodated at an additional charge. STORAGE & HANDLING Storage If panel bundles must be stored outside, strictly adhere to these requirements: If your metal panel order must be stored 1. Storage area should be level, and before use, store inside in a well-ventilated, should be located to minimize handling dry location. Moisture from condensation of bundle during construction.